STONE+AID
Stone Aid (CAN'STONE Repair Set)
Stone Aid is a repair kit exclusively for the stone tile "CAN'STONE". Simply apply it to seamlessly repair cracks and screw holes that appear after construction. It also has moderate elasticity, which helps prevent cracks from reoccurring.
SUGGESTION
Recommended joint width and usage amount
Joint width (mm)
'-
'-
MT-MEJI usage (25kg bag)
-
-
-
-
-
-
Outdoor walls
Indoor walls
Indoor floor
Outdoor floor
Slipperiness
Frost resistance
SUGGESTION
推奨目地幅と使用量の目安
Joint width (mm)
MT-MEJI usage (25kg bag)
'-
'-
-
-
-
-
-
-
Outdoor walls
Indoor walls
Indoor floor
Outdoor floor
Slipperiness
Frost resistance
SA-M-B
SA-M-B
STONE＋AID Mﾊﾟｯｹｰｼﾞ標準色 20mm幅で約5m補修
Joint Color
Joint Finishing
Joint Pattern
-
-
-
Item
Thickness
Qty/Box
Sqm/Box
Pcs/Sqm
Weight / Case
Price
Dimensions (mm)
SA-M-B
-
-
10set
-
4kg
¥4,600
¥4,600/set
M
Our works
Construction examples
-This product is available in a range of colors from CAN'STONE's color range, so the color may not be exactly the same as the color of the area to be repaired.
・Store in a place between 5°C and 35°C away from direct sunlight.
- Do not carry out work when the temperature is below 5°C.
-Please keep out of reach of children.
After application, avoid getting water on the repaired area until it dries.
・This product is water-based, but it will not dissolve in water once it dries. Wash any tools you have used with water before they dry.
- After opening, use it all at once.
・When working, wear gloves, etc. and avoid direct contact. In the unlikely event of an accident, please follow the first aid procedures below.
・If in eyes: Immediately wash face with tap water for at least 15 minutes and consult a doctor. If on skin, rinse with plenty of water and consult a doctor if necessary.
If you feel unwell after inhaling the gas, move to a place with fresh air immediately and seek medical advice if necessary.
-If swallowed: Seek medical attention immediately.
Video
movie
Precaution
注意事項
●M Package
Capacity: 200g
Amount used: 20mm width for approximately 5m of repair
*When ordering, please specify the grout color along with the CAN'STONE part number for the area of use.
Installation Method
0. What to prepare
STONE AID
Polivela et al.
Protective vinyl sheet
Masking tape
1. Preparation
First, remove any dirt from the area to be repaired by scrubbing with a brush or similar.
■Notes
If you use liquids, rinse with fresh water (do not use acidic cleaners) and allow the surface to dry completely before applying STONE AID.
2. Brick tile repair work
[ Undercoat ]
Apply STONE AID base color to all repair areas, rubbing it into cracks and screw holes.
■Notes
Immediately after application, STONE AID itself may appear whitish, but after drying (when all work is completed), it will become the same color as STONE. Please proceed to the next work, [Adding Nuance], without waiting for the [Undercoat] to dry.
[Adding nuance]
Apply uneven colors according to the pattern.
■ POINT
Aim for a coating thickness of about 1mm. (If it is too thick, it will take a long time to dry.)
■ POINT
If there is a color that cannot be expressed with a single color, mix the basic base with a mottled color to adjust the color.
Applying the paint roughly will give a more natural look.
3. Joint repair work
Select the appropriate grout colour from STONE AID and apply it to the repair area.
■ POINT
Just to be on the safe side, please check that there are no cracks in the joints of the upper and lower rows as well.
In some cases, cracks may occur along the same vertical line.
4. Verification and inspection
Allow to dry for at least 2 hours, then check the color of the repaired area.
If you are concerned about the color of the repaired area, apply a little of the STONE AID around the repaired area to blend it in with the overall color.
Other items
Submaterials
Manual
manual
SAMPLE ORDER
Proceed to sample request
Add paragraph text.
Add paragraph text.
Add paragraph text.
Proceed to procedure